 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| A Product Line of Diodes Incorporated ZXLD1322 BUCK/BOOST MODE DC-DC CONVERTER FOR LED DRIVING WITH 700mA OUTPUT AND CURRENT CONTROL Description The ZXLD1322 is an inductive DC-DC converter, with an internal switch, designed for driving single or multiple LEDs in series up to a total of 700mA output current. Applications cover input voltages ranging from 2.5V to 15V. Depending upon supply voltage and external components, this can provide up to 12W of output power. The device employs a variable 'on' and 'off' time control scheme with adjustable peak switch current limiting and operates in Buck/Boost mode, offering higher power efficiency and lower system cost than conventional PFM buck/boost circuitry. The device includes the DC-DC converter, a high-side current monitor and an NPN switching transistor to provide an integrated solution offering small PCB size, competitive cost/performance, high power efficiency of DC-DC conversion and maximum LED brightness/reliability. More importantly, it retains design flexibility to add customer specific features. The feedback control circuitry inside the ZXLD1322 provides excellent load and current regulation, resulting in very stable LED current over the useful life of the battery and over the full operating temperature range. The LED current can be adjusted from 100% down to 10% of the set value by applying a dc voltage to the ADJ pin and down to 1% by applying a PWM signal. An on-chip LED protection circuit also allows output current to be reduced linearly above a predetermined threshold temperature using an external thermistor at the TADJ pin. External resistors set nominal average LED current and coil peak current independently. The device can be shut down by applying a continuous low level dc voltage to the ADJ pin. Features * * * * * * * * * * * * 2.5V to 15V Input Voltage Range Up to 700mA output current # Typical efficiency >80% User-defined thermal control of LED output current using external thermistor High output current stability over input voltage and temperature 12A typical standby current LED current adjustable from 100% down to 2% Adjustable Soft-Start Capable of driving 3 LEDs in series Pin Assignments Applications * * * High power LED flashlights LED back-up lighting General LED lighting (Top View) DFN4030-14 with Exposed Pad 4mm x 3mm 0.50mm pitch 1.5W @ TA = 70C Typical Application Circuit DFN4030-14 Package(Bottom View) 45 chamfer denote Pin 1 Notes: #. Using standard external components as specified under electrical characteristics. Efficiency is dependent upon external component types and values. Higher efficiency is possible with alternative coils. ZXLD1322 Document number: DS32166 Rev. 3 - 2 1 of 17 www.diodes.com April 2010 (c) Diodes Incorporated A Product Line of Diodes Incorporated ZXLD1322 Block Diagram ZXLD1322 Document number: DS32166 Rev. 3 - 2 2 of 17 www.diodes.com April 2010 (c) Diodes Incorporated A Product Line of Diodes Incorporated ZXLD1322 Pin Description Name Pin # Description Adjust input * Leave floating, or connect to VREF to set 100% output current. * Drive with dc voltage. (50mV 1 BIAS 2 CFB N/C ISENSE EMITTER1 EMITTER2 COLLECTOR2 COLLECTOR1 N/C M_VIN 3 4 5 6 7 8 9 10 11 VIN 12 TADJ 13 VREF Exposed Pad 14 15 ZXLD1322 Document number: DS32166 Rev. 3 - 2 3 of 17 www.diodes.com April 2010 (c) Diodes Incorporated A Product Line of Diodes Incorporated ZXLD1322 Absolute Maximum Ratings (Voltages to GND Unless Otherwise Stated) Symbol TOP TST TJ PTOT Parameter Operating Temperature Storage Temperature Junction Temperature Package Power Dissipation DFN14 with Exposed Pad: 4mm x 3mm, 0.5mm Pitch Rating -40 to 125 -55 to 150 -40 to 150 1.5 at TAMB =70C Units C C C W DC-DC Converter Supply Voltage (VIN) ADJ CFB ISENSE TADJ BIAS -0.3V to +15V -0.3V to The lower of (+5.0V) or (VIN + 0.3V) -0.3V to The lower of (+5.0V) or (VIN + 0.3V) -0.3V to The lower of (+5.0V) or (VIN + 0.3V) -0.3V to The lower of (+5.0V) or (VIN + 0.3V) -0.3V to The lower of (+5.0V) or (VIN + 0.3V) High-Side Current Monitor Monitor Supply Voltage (M_VIN) Continuous Sense Voltage (M_VIN - M_LOAD) -0.3V to +15V -0.3V to +5V Switching NPN Transistor Symbol VCBO VCEO ICM IC Parameter Collector-Base Voltage Collector-Emitter Voltage Peak Pulse Current Continuous Collector Current Rating 18 18 3 (Pulsed Width = 300s. Duty Cycle<=2%) 2 Units V V A A These are stress ratings only. Operation outside the absolute maximum ratings may cause device failure. Operation at the absolute maximum ratings for extended periods may reduce device reliability. Thermal Resistance Junction to ambient (RJC) DFN4030-14 Nominal Value 26.3C/W ZXLD1322 Document number: DS32166 Rev. 3 - 2 4 of 17 www.diodes.com April 2010 (c) Diodes Incorporated A Product Line of Diodes Incorporated ZXLD1322 Electrical Characteristics (Test conditions: VIN = 4V, TAMB = 25C unless otherwise stated(a)) DC-DC Converter Supply Parameters Symbol VIN VIN(Start) VUVVUV+ Iq ISTBY VREF TCO(REF) Notes: Parameter Supply Voltage Supply voltage for start-up(b) Under-voltage detection threshold normal operation to start-up mode Under-voltage detection threshold start-up mode to normal operation Quiescent Current Standby Current Internal Reference Voltage Internal Reference Temperature Coefficient Condition Normal Operation Start-up mode VIN falling VIN rising Measured into VIN ADJ pin floating. Excluding switch base current). Measured into VIN. ADJ pin grounded ADJ pin floating 2.5V Typ. Max. 15 2.4 Unit V V V V mA 1.8 2.2 1.5 12 480 500 50 20 520 A mV ppm/K (a) Production testing of the device is performed at 25C. Functional operation of the device and parameters specified from -40C to +125C are guaranteed by design, characterization and process control. (b) Between 1.2V and 2.2V the device will run in the Low Voltage Startup Mode (for details refer to section "Low Voltage Operation") DC-DC Converter Input Parameters Symbol VSENSE VSENSE (SU) Parameter Peak switch current sense voltage Peak switch current sense voltage in start-up mode Sense input current Control loop compensation capacitor External DC control voltage applied to ADJ pin to adjust output current Switching threshold of ADJ pin Temperature coefficient of VADJ(th) Internal resistor between VREF and ADJ Clamp voltage on ADJ pin Condition Measured on ISENSE pin CFB pin at 0V Measured on ISENSE pin. Start-up mode VIN = 1.2V Measured into ISENSE with pin at 0V. CFB pin at 0V Min. 45 Typ. 55 10.5 Max. 65 Unit mV mV ISENSE CFB VADJ VADJ(th) TCO (VADJ) RADJ VADJ (CLMP) -15 -7 10 -1 A DC brightness control mode Standby state to normal operation 50 26 28 +0.3 500 30 mV mV %/K k mV VADJ<550mV 100A injected into ADJ pin 100 575 DC-DC Converter Output Parameters Symbol Toff(100) Toff(10) fLXMAX fSU Parameter Discharge pulse width Discharge pulse width Maximum operating frequency Switching frequency in start-up mode Condition 100% Output current 10% Output current VIN = 1.2V Min. 0.7 4 Typ. 1.2 8 50 Max. 1.7 12 600 Unit s s KHz KHz ZXLD1322 Document number: DS32166 Rev. 3 - 2 5 of 17 www.diodes.com April 2010 (c) Diodes Incorporated A Product Line of Diodes Incorporated ZXLD1322 Switching NPN Transistor Symbol ISW IBON(max) IBON V(BR)CE VCE(sat) hFE COBO t(on) t(off) Parameter (c) Average continuous switch current Maximum base current into switch transistor from internal drive circuit(d) Base current into switch transistor using external resistor (RBASE) from BIAS pin to ground Collector-Emitter breakdown voltage Collector-Emitter saturation voltage Static forward current transfer ratio Output capacitance Turn-on time Turn-off time Condition Min. Typ. Max. 2 70 Unit A mA mA V 50 120 209 116 64 30 28 pF ns ns mV 2V 50 10 15 High-Side Current Monitor Symbol VM_VIN VMON I_M_VIN TCO(MON) BW Gm ACC Parameter Supply voltage Sense voltage Input current Temperature coefficient Bandwidth Tran conductance IOUT/VMON Accuracy RM = 0.1 VMON = 100mV -3 Condition =V(VIN) - VM_VIN Measured into M_VIN pin VMON=10mV VMON=100mV VMON=10mV VMON=100mV Min. 2.5 0 Typ. 100 0.08 370 150 350 2.5 1 3 Max. 18 200 1 Unit V mV A ppm/K KHz Mhz mA/V % Reference Current Monitor Symbol VADJ TCO (MON) Parameter Adjust Voltage Temperature coefficient Bandwidth Tran conductance IOUT/VADJ Accuracy Condition VADJ = 50mV VADJ = 500mV VADJ = 50mV VADJ = 500mV Min. 0 Typ. 160 200 275 3 200 Max. 500 Unit mV ppm/K KHz Mhz A/V BW Gm ACC Notes: VADJ = 500mV -3 3 % (c) Measured under pulse conditions. (d) This current is measured via the collectors and emitters of the switch with these connected to ground (0V) (e) Measured under pulse conditions. Peak Current = IC ZXLD1322 Document number: DS32166 Rev. 3 - 2 6 of 17 www.diodes.com April 2010 (c) Diodes Incorporated A Product Line of Diodes Incorporated ZXLD1322 LED Thermal Control Circuit (TADJ) Parameters Symbol VTADJH VTADJL Gm(TADJ) Parameter Upper threshold voltage Lower threshold voltage Trans conductance IOUT/VTADJ Condition Onset of output current reduction (VTADJ falling) Output current reduced to <10% of set value (VTADJ falling) Min. Typ. 75 50 4 Max. Unit mV mV mA/V Output Current Regulation Parameters Symbol IOUT IOUT TCO I(OUT) IOUT/ IOUT IOUT/ VIN Eff Notes: Parameter Minimum output/ LED current Output current accuracy(g) Output current temperature drift Load Current Regulation Line Voltage Regulation of output current Efficiency (f) Condition VIN > 3V 3.0V < VIN < 15V, IOUT = 700mA, VADJ = 100mV, 3.0V < VIN < 15V, Iout = 700mA, VADJ = 100mV 350mA < I(LED) < 700mA Min. Typ. 0.75 Max. Unit A -5 100 2 0.5 +5 200 % ppm/K %/A %/V % 350mA < I(LED) < 700mA 85 (f) System parameter only. This value is dependent upon external components and circuit configuration. (g) This refers to the accuracy of output current regulation under normal operation when the feedback loop incorporating the current monitor is active. The tolerances of external components are not included in this figure. ZXLD1322 Document number: DS32166 Rev. 3 - 2 7 of 17 www.diodes.com April 2010 (c) Diodes Incorporated A Product Line of Diodes Incorporated ZXLD1322 Device Description The ZXLD1322 is a buck/boost mode inductive DC-DC converter, with an internal switch, designed for driving single or multiple LEDs in series up to a total of 700mA output current. Depending upon supply voltage (VIN), LED forward voltage drop (VLED) and circuit configuration, this can provide up to 12W of output power. Applications cover VIN ranging from 2.5V to 15V. The device employs a modified Pulse Frequency Modulation (PFM) control scheme, with variable "ON" and "OFF" time control and adjustable peak switch current limiting. General device operation (refer to block diagram) Normal Operation Control is achieved by sensing the LED current in a series resistor (RM), connected between the two inputs of the LED Current Monitor. This generates a proportional current (IMON) that charges the external integrator capacitor CFB. IMON is balanced against a reference discharge current (IADJ) generated at the output of a second voltage to current converter driven from the demand voltage (VADJ) on the ADJ pin. The difference between IMON and IADJ is integrated by CFB to produce an error voltage. A comparator takes a summed version of the voltage at the ISENSE pin and a fraction of this CFB voltage and resets the latch driving the switch when the sum is greater than 50mV. The switch transistor is turned on by the output of the SR latch, which remains set until the emitter current in the switch transistor produces a voltage drop VSENSE (=50mV nominal) in external resistor RSENSE, defining a preset maximum switch current of 50mV/RSENCE. Operation is such that a rising error voltage on CFB will effectively lower the voltage required on the ISENSE pin and therefore reset the latch earlier in the switching cycle. This will reduce the 'ON' time of the switch and reduce the peak current in the switch from its preset maximum value. Similarly, a falling error voltage will reset the latch later and the peak switch current will be increased. The control loop therefore reduces or increases the energy stored in the coil during each switching cycle, as necessary, to force the LED current to the set value. This results in high accuracy, as no error is needed in the LED current to drive the servo to the required region. The time taken for the coil current to reach the peak value depends on several factors: the supply voltage, the peak coil current required at that particular LED power and whether the system operates in "continuous" or "discontinuous" mode. The time allowed for the coil current to discharge into the LED is fixed by the 'Variable Off Delay' monostable, whose period is modified by the power demand signal on the ADJ pin. This monostable determines the time for which the latch remains reset (switch off) and provides a longer "OFF" period at lower power settings, helping to keep the parameters within an acceptable range. Note that the "ON" period and the "OFF" period are set by the supply voltage, LED power and external components chosen. The frequency is therefore determined by these parameters and is NOT fixed. In this modified PFM scheme, the external components can be chosen to keep the frequency well above the audio range for all extremes of parameters, so no audible whistling should ever occur. The 500mV reference voltage defines the nominal VADJ voltage and this defines the 100% output current. For lower LED currents, the ADJ pin can be-driven from an external DC voltage (50mV For supply voltages below 2V, the normal control loop will have insufficient headroom to operate reliably. This condition is detected by the 'under-voltage comparator', which compares a fraction of the internal supply voltage (VCC) against VREF. When the comparator output is active (VCC<1.8V), the output of the normal switch drive circuit is disabled and an alternative 'Start-up oscillator and driver' enabled. The start-up oscillator provides a nominal 50kHz fixed frequency drive signal to the base of the switch transistor, which is independent of VADJ and the voltage on CFB. Under low voltage conditions, the peak current in the coil ramps to approximately 25% of the normal value and the "OFF" time is fixed. The low voltage start-up mode allows the device to operate down to 1.2V nominal. This allows the chip to work from a single cell. ZXLD1322 Document number: DS32166 Rev. 3 - 2 8 of 17 www.diodes.com April 2010 (c) Diodes Incorporated A Product Line of Diodes Incorporated ZXLD1322 ADJ pin The ADJ pin is connected to the internal 500mV reference (VREF) via a 100k resistor. This biases the ADJ pin to the reference voltage and defines nominal 100% LED current. The ADJ pin can be overdriven with an external dc voltage between 50mV and 500mV to reduce the LED current proportionally between 10% and 100% of the nominal value. LED current can also be adjusted by applying a low frequency PWM signal to the ADJ pin to turn the device On and Off. This will produce an average output current proportional to the duty cycle of the control signal. The device can be shut down by shorting the ADJ pin to ground, or pulling it to a voltage below 28mV with a suitable open collector NPN or open drain NMOS transistor. In the shutdown state, most of the circuitry inside the device is switched off and residual quiescent current will be typically 12A. Thermal control of LED current The 'Thermal compensation current' circuit produces a sourcing current (Itc) which is zero for voltages above 75mV on TADJ and increases to 100A when TADJ falls to 50mV. This current is summed into the control node and subtracted from the demand current, causing LED current to reduce from 100% down to zero over this input range. The potential divider, consisting of a fixed resistor Rt and an NTC Thermistor Rth between VREF and ground, defines the voltage on TADJ and sets the threshold temperature. Further details are given in the application notes. The Thermal Control feature can be disabled by leaving the TADJ pin floating, or by connecting it to VREF. Over-temperature shutdown The ZXLD1322 incorporates an over-temperature shutdown circuit to protect the device against damage caused by excess die temperature, resulting from excessive power dissipation in the switch. The output of the 'Over-temp Shutdown' circuit will go high when the die temperature exceeds 150C (nominal). This will turn off the drive to the switch during normal operation. Operation will resume when the device has cooled to a safe level. ZXLD1322 Document number: DS32166 Rev. 3 - 2 9 of 17 www.diodes.com April 2010 (c) Diodes Incorporated A Product Line of Diodes Incorporated ZXLD1322 Application Notes Setting Peak Coil Current The peak current in the coil is set by the resistor (RSENSE) between the switch emitter and ground according to: ISWPEAK = 50mV RSENSE The minimum peak current will depend on operating mode, coil inductance and supply voltage range. The maximum peak current must not exceed the specified value for the switch. (See Application circuits for details) Setting LED Current The nominal average LED current is given by: ILED (NOM) = 100mV RM Where RM is the external resistor connected between pins M_VIN and VIN. This current can be adjusted to a lower value by applying a dc control voltage or PWM control signal to the ADJ pin. DC Control The LED current can be adjusted over a 10% to 100% range by connecting a variable resistor RADJ from the ADJ pin to ground to vary the DC voltage at the ADJ pin. RADJ forms the lower part of a resistive divider and the internal 100k resistor between the ADJ and VREF pins forms the upper part. A value of 1M for RADJ will therefore give a maximum current of 91% of ILED (nom) and the device will be turned off when the voltage on the ADJ pin falls below 28mV, corresponding to an RADJ value of approximately 5k. If required, an end-stop resistor in series with RADJ can be used to maintain the voltage on the ADJ pin above the turn-on threshold. Using a logarithmic potentiometer for RADJ will give an approximately linear variation of output current with shaft rotation. (Fig 1) If required, the maximum output current can be restored to 100% by adjusting the value of the LED current monitor resistor (RM). The tolerance of the internal 100k resistor and RADJ should be taken into account when calculating output current. The ADJ pin is clamped internally to a voltage of 575mV (nom), to limit maximum average output current to approximately 115% of ILED(nom). Fig. 1 ZXLD1322 Document number: DS32166 Rev. 3 - 2 10 of 17 www.diodes.com April 2010 (c) Diodes Incorporated A Product Line of Diodes Incorporated ZXLD1322 PWM Control A wider dimming range can be achieved by applying a PWM control signal to the ADJ pin to turn the device on and off, giving an average output current proportional to the duty cycle of the control signal. The ADJ pin can be driven directly from the open drain NMOS output of a microcontroller, or indirectly with a low saturation voltage NPN transistor such as the Zetex ZXTN25015DFL. (Fig 2). ZXTN25015DFL Fig. 2 In the circuit of Fig 4, the average LED output current will be: ILED (AVG) = ILED(NOM) *D Where duty cycle A PWM frequency of 200Hz, or lower is recommended, to minimize errors due to the rise and fall times of the converter output. Thermal Compensation of LED Current High-luminance LEDs often need to be supplied with a temperature compensated current in order to maintain stable and reliable operation at high temperatures. This is usually achieved by reducing the LED current proportionally from its nominal set value when the LED temperature rises above a predefined threshold. (Fig.3) Fig. 3 The 'Thermal compensation current' generator inside the ZXLD1322 provides the necessary thermal compensation current to meet this requirement, using an NTC thermistor and resistor. (Fig 4) Fig. 4 ZXLD1322 Document number: DS32166 Rev. 3 - 2 11 of 17 www.diodes.com April 2010 (c) Diodes Incorporated A Product Line of Diodes Incorporated ZXLD1322 The TADJ pin of the device has a voltage threshold of 75mV nominal, which is derived from the reference voltage VREF. If the voltage (VTADJ) on the TADJ pin is held above the threshold, the thermal compensation current will be zero and no thermal compensation is applied. However, if VTADJ falls below the threshold, a thermal compensation current (ITC) is produced that is proportional to VTADJ. ITC is injected into the control loop in such a way as to reduce the demand current IADJ, causing the control loop to decrease the LED current. The LED current will be reduced to less than 10% of the set value when VTADJ falls below 50mV. The threshold voltage has been chosen to set a nominal threshold of 105C and the device has been optimized to operate with a standard 103KT1608 thermistor and 5k resistor in the potential divider. Circuit details are given in the application notes. Alternative thermistor/resistor networks can be used providing the input resistance presented to the device at the TADJ pin is similar at the threshold temperature. If no LED thermal compensation is required, the TADJ pin should be connected to VREF to disable this function. ZXLD1322 Document number: DS32166 Rev. 3 - 2 12 of 17 www.diodes.com April 2010 (c) Diodes Incorporated A Product Line of Diodes Incorporated ZXLD1322 Typical Operating Conditions Inductive converters can operate in either CONTINUOUS mode, where current always flows ithe inductor, but rises during the ON period and falls during the OFF period, or DISCONTINUOUS mode, where the current falls to zero during the OFF period. The mode depends on several factors, including supply voltage, output (LED) voltage and the choice of peak current and inductor value. Calculations need to be done to determine which mode the converter will be in. The circuit should be designed to give slightly more LED current than required under the lowest supply voltage, so the control loop can regulate the current accurately. If the theoretical LED current is less than that required, the control loop will not be able to reach the required value. The calculations will give an idea of the ON and OFF times and hence the operating frequency, but bear in mind that the control loop will reduce the peak current to achieve the exact programmed LED current and this will raise the operating frequency. In general, values in the discontinuous mode are simpler to calculate because the current can go from zero to the theoretical maximum during the ON period and fall to zero during the OFF period. In continuous mode the current will start from some value, so the ON time will be lower to reach the theoretical maximum and lower still when the control loop reduces the peak current below the maximum. Circuit Operation Operation of buck / boost LED driver Used when the input voltage can go higher or lower than the LED voltage, this circuit has an ON phase, where the coil is connected from the supply to ground and an OFF phase, where the coil current flows through the LED via a Schottky diode. The current therefore only flows into the LED circuit during the OFF phase, although the reservoir capacitor C3 should keep current flowing in the LED(s) continuously. The important difference is that this circuit has the LED cathode taken to VIN instead of ground. ADJ is set between 50mV and 500mV to give between 10% and 100% power respectively. Making R2 = ZERO gives a base current to the output transistor of 50mA nominal and making R2 = 1.68k gives 10mA nominal. The reduced base current will lower supply current and hence improve efficiency in lower power applications. Making R1 = 25m gives a peak coil current of 2 Amps. The internal power transistor turns on until the coil current builds up to the peak value. At this point the transistor switches off and the coil current continues to flow in the LED(s) via the Schottky diode D1. With a buck converter, the LED is in series with the coil, so no coil current can flow until the supply voltage exceeds the LED forward drop. The circuit will not work if the supply is less than this. With a boost converter, there is always a path from supply to ground through the coil, Schottky diode and LED in series, so if the supply voltage is greater than the LED and Schottky forward drops, unlimited current will flow in the LED. The circuit will not work if the supply is greater than this. Thus neither circuit will work for both conditions, where the supply could be either higher or lower than the LED forward drop, for example when using 3 cells to supply it. Although it looks like a boost circuit, taking the LED cathode to the supply means that no current can flow in the LED even if the supply is greater than the forward drop. However, because the coil is still connected straight across the supply during ZXLD1322 Document number: DS32166 Rev. 3 - 2 13 of 17 www.diodes.com April 2010 (c) Diodes Incorporated A Product Line of Diodes Incorporated ZXLD1322 the ON phase, the current can still be established when the supply is less than the LED forward drop. Hence this circuit will work at supply voltages above and below the forward LED drop. This mode is useful for example when using 3 cells and a white LED, where the voltage of 3 fully charged alkaline cells is more than the LED forward drop, but the voltage of 3 partly discharged rechargeable NiCd cells is less than the LED forward drop. The LED current is sensed by R3 and the controller varies this until the drop in R3 equals 20% of VADJ. Hence making R3 = 100m and VADJ = 500mV gives a LED current of 1 Amp because the 500mV VADJ results in 100mV across R3 which equals 1 Amp. Making VADJ = 10mV gives a LED current of 100mA because the 50mV VADJ results in 10mV drop across R3 which equals 100mA. The power is controlled by the chip backing off the peak coil current, so it is necessary to calculate the coil inductance and current to guarantee slightly more than 100% LED power, so the circuit can control it effectively. The internal control loop is compensated by C1, which is normally 10nF. If the thermistor (R5) is used, the power will be backed off progressively as the TADJ pin goes low. With the TADJ pin above 75mV, power is 100% and this is reduced to zero when the TADJ pin reaches 50mV. Making R4 = 5k and using a 103KT1608 thermistor, the thermistor will reach 869 at 105C giving VTADJ = 74mV which will start to reduce the LED power above 105C. By 125C the thermistor will reach 547 giving VTADJ = 50mV which gives zero power. This will protect the LED from damage. These temperature values can be set by the customer by using a different thermistor or a different value of R4. If protection is not required, leaving the TADJ pin open circuit will make it float to a high voltage and always give 100% power. Bill of materials Reference U1 D1 L1 L1 L1 C1 C2 C3 R1 R2 R3 R4 R5 Part No ZXLD1322 ZHCS2000 MSS7341-103ML NPIS64D100MTRF 744 777910 Generic GRM31CR71H475K GRM31MR71E225K Generic Generic Generic Generic Thermistor NTC Value LED Driver Schottky diode 10H 2A 10H 2A 10H 2A 10nF 10V 4.7F 50V 2.2F 25V 25m 1.5k 100m 5.1k 10k Manufacturer Zetex Zetex Coilcraft NIC Wurth Generic 0603 Murata 1206 Murata 1206 Generic 0805 Generic 0603 Generic 0805 Generic 0603 103kt1608 www.murata.com www.murata.com www.coilcraft.com www.niccomp www.wurth.co.uk Contact Details www.zetex.com ZXLD1322 Document number: DS32166 Rev. 3 - 2 14 of 17 www.diodes.com April 2010 (c) Diodes Incorporated A Product Line of Diodes Incorporated ZXLD1322 Additional Notes Note that the ON time is set by the time it takes the coil to reach the peak current. This peak value is reduced by the control loop to give the desired LED power, so the ON time can vary over a wide range. The minimum coil current can be zero (discontinuous operation) or finite (continuous operation) depending on the supply voltage, LED current and the LED voltage. The OFF time is set by an internal timer and is nominally 1.2s at 100% LED power (VADJ = 500mV), increasing to about 8s at 10% LED power (VADJ = 50mV). The longer OFF time and variable peak current enables the circuit to dim the LED whilst maintaining continuous switching, rather than "skipping" or stalling and continuous running is better for reducing electrical noise and also for eliminating audible noise from the coil core. Layout Considerations As with all switching DC to DC converters, the currents can be large. Using small inductors with a reasonable high supply voltage will cause currents to change quickly. High dI/dt can cause inductively-coupled spikes into adjacent tracks. At the transition from of the ON phase to the OFF phase and back, where the power transistor switches, the voltage at the collector rises and falls quickly. High dV/dt can cause capacitively coupled spikes into adjacent tracks, especially if they have a high impedance. For this reason, all tracks on the PCB should be thick, to minimise drops, and short to keep all the components coupled tightly together. A double-sided board should be used with a ground plane to screen the tracks and provide a good ground return for the various functions and the rear exposed pad on the package should have an appropriately-sized land with good ground connections, both to reduce electrical noise due to ground drops and to improve thermal conductivity. The input decoupling capacitor C1 should be very close to the chip pins and the LED sense resistor R3 should have Kelvin tracks to M_VIN and VIN to achieve LED current measurement accuracy, as the PCB tracks will have comparable resistance to the 100m resistor, so taking sense tracks to the current monitor which are not connected close to the ends of R3 will cause a measurement error. The peak current sense resistor R1 should have short tracks to the ground at the bottom end and Kelvin tracks to ISENSE at the top end. This resistor might need to be only 25m and PCB track resistance becomes comparable if the tracks are not very short. ISENSE is a high impedance input, so a thin track from this pin directly to the top of RSENSE resistor R1 will still give an accurate measurement. The ADJ pin should have short tracks, as this is a fairly low-level signal controlling the power of the system. As it needs to be less than 28mV for shutdown, a close ground connection is needed for the pull-down device, as any ground drops could raise the potential. In particular, if a bipolar transistor is used as a pull-down device, this will have an appreciable VSAT, which could perhaps be half the shutdown potential. The bottom of the thermistor must be coupled very closely to ground, as the TADJ pin varies the LED current from 100% to 0% for a voltage change of only 25mV, so any noise on the bottom of the thermistor will seriously affect the accuracy of the Thermal Protection circuit. Ordering Information Device ZXLD1322DCCTC Reel Size (mm) 33.02 Reel Width (mm) 12 Quantity per reel 3000 Device Mark 1322 ZXLD1322 Document number: DS32166 Rev. 3 - 2 15 of 17 www.diodes.com April 2010 (c) Diodes Incorporated A Product Line of Diodes Incorporated ZXLD1322 Package Outline - DFN4030-14 E A A3 E2 PIN #1 IDENTIFICATION CHAMFER 0.300 X 45 PIN 1 DOT BY MARKING D2 D L A1 DIM Min A A1 A3 b D Inches Max 0.0354 0.002 Millimeters Min 0.80 0.00 Max 0.90 0.05 DIM Min D2 e E E2 L Inches Max 0.1279 Min 3.15 e b Millimeters Max 3.25 0.50 BSC 2.95 1.65 0.35 3.05 1.75 0.45 0.0315 0.00 0.1240 0.0197 BSC 0.1161 0.0650 0.0138 0.1201 0.0689 0.0177 0.008 REF. 0.0079 0.1555 0.0118 0.1594 0.203 REF. 0.20 3.95 0.30 4.05 Note: Controlling dimensions are in millimeters. Approximate dimensions are provided in inches ZXLD1322 Document number: DS32166 Rev. 3 - 2 16 of 17 www.diodes.com April 2010 (c) Diodes Incorporated A Product Line of Diodes Incorporated ZXLD1322 IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systemsrelated information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright (c) 2010, Diodes Incorporated www.diodes.com ZXLD1322 Document number: DS32166 Rev. 3 - 2 17 of 17 www.diodes.com April 2010 (c) Diodes Incorporated |
Price & Availability of ZXLD1322DCCTC
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |